<?xml version="1.0" encoding="utf-8"?>
	<rss version="2.0">
		<channel>
			<title>Green Building Forum - MVHR planning: maintenance elbow room and positioning</title>
			<lastBuildDate>Wed, 10 Jun 2026 10:14:46 +0100</lastBuildDate>
			<link>https://www.greenbuildingforum.co.uk/newforum/</link>
			<description></description>
			<generator>Lussumo Vanilla 1.0.3</generator>
			<item>
		<title>MVHR planning: maintenance elbow room and positioning</title>
		<link>https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306935#Comment_306935</link>
		<guid isPermaLink="false">https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306935#Comment_306935</guid>
		<pubDate>Mon, 07 Oct 2024 07:22:08 +0100</pubDate>
		<author>stonecold</author>
		<description>
			<![CDATA[Hi, we are renovating and getting a zehner comfoair Q 350 (725mm w, 570mm deep, 850mm high, weighing 50kg) and planning to wall mount it - what kind of elbow room is needed for servicing? The room we are planning to put it in is 900mm wide on the wall we hope to hang it (900x1300mm room) which we've been told could be tricky to fit the bends in, but what space do we need for elbow room for servicing? Even worse we may end up digging down under it to insulate the uninsulated floor below.<br /><br />We could fit in on the other wall which is 400mm ish wider, but this means having 50kg MVHR plus ducting attached to a stud wall / dry lined solid stone wall. Will it be strong enough or could we run into issues during installation or  later on?<br /><br />Lastly, is it right that the condensate drain needs to run at a gradual slope (ie gravity fed) or does the water get pumped out, and can this drain into a toilet cistern or internal soil pipe - or will that be horribly unpleasant? I'm not looking forward to running the condensate drain around 3 walls to get to the plumbing.]]>
		</description>
	</item>
	<item>
		<title>MVHR planning: maintenance elbow room and positioning</title>
		<link>https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306942#Comment_306942</link>
		<guid isPermaLink="false">https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306942#Comment_306942</guid>
		<pubDate>Mon, 07 Oct 2024 11:53:21 +0100</pubDate>
		<author>djh</author>
		<description>
			<![CDATA[<blockquote ><cite >Posted By: stonecold</cite>what kind of elbow room is needed for servicing?</blockquote>The installation manuals normally specify what space is needed. As regards the ducting, do some drawings and buy at least some of the ducting parts and have a play. Or pay somebody to design it. All the plasterboard type materials have specs that state permitted loadings.<br /><br />Condensate drains normally need to be gravity fed, yes, and you MUST use a dry trap (HepVO or similar) because the water in a wet trap will evaporate. Ours goes into a nearby foul waste pipe but any waste pipe is fine.]]>
		</description>
	</item>
	<item>
		<title>MVHR planning: maintenance elbow room and positioning</title>
		<link>https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306945#Comment_306945</link>
		<guid isPermaLink="false">https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306945#Comment_306945</guid>
		<pubDate>Mon, 07 Oct 2024 17:55:32 +0100</pubDate>
		<author>Artiglio</author>
		<description>
			<![CDATA[Whilst access for servicing may well not be too great, check as to what needs to be done for replacing of internal parts. I’ve vent axia sentinel kinetics, they need next to no space for routine servicing, but to do just about anything else requires the unit to be removed from the wall. Rubbish design.]]>
		</description>
	</item>
	<item>
		<title>MVHR planning: maintenance elbow room and positioning</title>
		<link>https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306946#Comment_306946</link>
		<guid isPermaLink="false">https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=306946#Comment_306946</guid>
		<pubDate>Mon, 07 Oct 2024 20:52:20 +0100</pubDate>
		<author>djh</author>
		<description>
			<![CDATA[Also check there's enough space to stand somewhere convenient whilst servicing it. The manuals sometimes specify the space needed for the MVHR & its parts, but not for a human being holding one or both of them :(]]>
		</description>
	</item>
	<item>
		<title>MVHR planning: maintenance elbow room and positioning</title>
		<link>https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=307062#Comment_307062</link>
		<guid isPermaLink="false">https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=307062#Comment_307062</guid>
		<pubDate>Mon, 21 Oct 2024 13:28:03 +0100</pubDate>
		<author>stonecold</author>
		<description>
			<![CDATA[Thanks everyone! We have a designer already but are trying to figure out which of two walls to put it on. Height is fine there.]]>
		</description>
	</item>
	<item>
		<title>MVHR planning: maintenance elbow room and positioning</title>
		<link>https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=307066#Comment_307066</link>
		<guid isPermaLink="false">https://www.greenbuildingforum.co.uk/newforum/comments.php?DiscussionID=18208&amp;Focus=307066#Comment_307066</guid>
		<pubDate>Mon, 21 Oct 2024 17:05:45 +0100</pubDate>
		<author>djh</author>
		<description>
			<![CDATA[Is the construction of the two walls the same? Think about (a) the weight and (b) noise transmission. Also is the ducting simpler in one position or the other?]]>
		</description>
	</item>
	
		</channel>
	</rss>